Advertisement

Bill Hamilton, the Mackenzie Country engineer who taught a boat to climb a river

The braided Waimakariri River at sunset, threading hundreds of shallow channels through pale gravel

The American park ranger watching the New Zealanders at the foot of Lava Falls Rapid in July 1960 had been told the boats could climb the Colorado River. He did not believe it. The river there, in the deepest part of the Grand Canyon, drops thirteen metres in less than a kilometre. The standing waves are the size of houses. Powell’s expedition in 1869 had portaged. Almost everyone since had portaged. The idea that four small open boats from a country no one in Arizona could place on a map were going to drive up the rapid, into the white water, was the kind of thing tourists said.

Then Jon Hamilton, the inventor’s son, eased the throttle forward in the eighteen-foot Kiwi, the bow lifted, the jet behind him threw a rooster tail twenty feet into the desert air, and he started, slowly, to climb.

Advertisement

It took him two days to get all four boats up Lava. He drove one boat into the rapid, walked back down the canyon, drove the next, walked back. On some standing waves it took him half an hour to claw the boat over the top, the jet behind him spitting Colorado River back where it had come from at five thousand litres a minute. When he finished, the wave train had been made to flow in two directions at once, which is not something rivers do, and the boats were tied up at Lee’s Ferry, and the New Zealanders had, as a matter of plain physical fact, just driven up through the Grand Canyon.

The boats had been built in a shed at the foot of the Southern Alps by Jon’s father, a Mackenzie Country sheep farmer who had been knighted not yet, and would die not yet, but who, by 1960, had already done what the engineers in Detroit and Glasgow and Hamburg had not managed, which was to make a small high-powered boat that worked properly in shallow, fast, stony water. Sir Charles William Feilden Hamilton — Bill to anyone he had met more than once — was at home at Irishman Creek when the news came through from Arizona. He smoked his pipe. He was pleased. He did not say much.

Lava Falls Rapid on the Colorado River in the Grand Canyon, white water churning between dark walls
Lava Falls, the Grand Canyon’s largest rapid. In July 1960, Jon Hamilton spent two days driving four New Zealand jet boats up it. Photo Nate Loper, CC BY 2.0.

A high-country childhood

Hamilton was born on 26 July 1899 at Ashwick Station, near Fairlie, on the Canterbury side of the Two Thumb Range. His father William managed the run; his mother Cora Cannon had grown up in the same hard, cold, beautiful country. From the front verandah at Ashwick you could see, on a clear morning, almost the whole Mackenzie Basin.

Advertisement

It is a country that produces a particular kind of person. The growing season is short, the winters are long, and the nearest engineer with a lathe is a long way off. If a piece of farm machinery breaks in July, it is generally easier to fix it yourself than to wait for someone to drive up from Timaru. Hamilton grew up with a forge and a workshop and the assumption, never stated, that capable people built and repaired their own equipment. His mother, by family account, let him follow the farmhands and the blacksmiths around in preference to schoolwork, on the theory that he would learn more useful things that way. She was probably right.

He was sent down to Christ’s College in Christchurch, by way of Waihi Preparatory in Winchester. The school records suggest he was not the kind of pupil masters wrote home about. He did, however, build a small hydroelectric plant at home before he was fifteen, which is the kind of thing masters do not always notice, and which mattered more.

Advertisement

His older brother John was killed in the First World War. Bill, too young to enlist, finished school and helped on the home station. In 1921, when he was twenty-one, he bought Irishman Creek — a 10,000-hectare run on the Tekapo side of the Mackenzie Basin, with the Two Thumb Range at its back and the lake-bed terraces sloping away in front of it. He was, on paper, a high-country runholder. In practice, he was already running a small engineering company; the sheep, by the time he was finished, would be among the lesser things he did with the place.

Lake Pukaki with Aoraki Mount Cook in the distance, looking south across the Mackenzie Basin
The Mackenzie Basin from above Lake Pukaki, looking toward Aoraki Mount Cook. Bill Hamilton bought Irishman Creek Station, a few kilometres north of here, in 1921. Photo Annette Teng, CC BY 3.0.

Peggy, the Bentley, and the shed at Irishman Creek

In 1923 he married Margaret Wills — Peggy — and brought her back to Irishman Creek. Their son Jon Oliver Feilden Hamilton was born in 1925; their daughter June a few years later. Hamilton was, by then, also racing motor cars. In 1928 he set the Australasian land speed record at 109.09 mph, in a 4.5-litre Bentley, on a stretch of beach near Christchurch. He flew small aircraft. He survived a crash at Wellington’s Rongotai aerodrome in 1936 in which the pilot, the famous aviator Mac McGregor, was killed. He was not, in the conventional sense, a quiet man. He was simply not a noisy one.

The shed at Irishman Creek mattered more than the Bentley. Hamilton needed a hydro dam to power the homestead and the workshop, and the conventional horse-drawn earth scoops of the period were too slow. He designed his own. The Hamilton excavator, sometimes called the I.C. Excavator after Irishman Creek, was a tractor-towed earth-moving scoop that could be tipped and dragged with cables; it cut the labour cost of a small earthworks job by a useful margin. By the late 1930s he was selling them to local councils, to the Public Works Department, and eventually to British buyers. A 1939 brochure from CWF Hamilton & Co Ltd lists half a dozen models.

It was the excavator that paid for the next thirty years. It was also the excavator that taught Hamilton most of what he later needed to know about pumps. A Hamilton-built earth-moving scoop used at Hanmer Springs in the late 1930s on drainage and ditching contracts — the “Hanmer ditcher”, as the men on the job called it — was effectively a powered impeller chewing through wet ground. The principle of forcing a working fluid through a confined channel at speed, with vanes that could be redesigned at will, sat on his bench at Irishman Creek for the better part of a decade before he applied it to water and a hull.

By 1948 the company had outgrown the high country. Hamilton moved the manufacturing operation to Middleton, in west Christchurch, and started supplying heavy gear to the Waitaki hydroelectric schemes. CWF Hamilton & Co was, by then, a serious mid-size engineering firm. Its founder still drove home to Irishman Creek at weekends, and still kept a workshop in the woolshed.

Ski tows and the Hamilton Model B

In 1947, Harry Wigley — Peggy’s nephew, and the founder of what became Mount Cook Airlines — asked Hamilton to design a tow for the new ski field at Coronet Peak above Queenstown. New Zealand had skifields, in the loose sense; what it did not have, before Coronet Peak, was a lift that could move skiers up a slope in any number. Hamilton designed a rope tow with a sprung clip — the “nutcracker” — that gripped a moving wire rope. The skier clamped on, was hauled up the hill, and let go at the top. It was simple, cheap and indestructible. He installed a similar tow at Whakapapa on Mt Ruapehu in 1949. The perfected version, the Hamilton Model B, was still in commercial service on club fields in both islands and in Australia for the rest of the twentieth century. There are still nutcracker fields running them.

This is one of the small, reliable patterns of Hamilton’s career. The product had to be cheap enough that an alpine club could afford one; it had to be repairable in a tin shed by a member with a spanner; it had to keep working in driving sleet. He thought about the user before he thought about the elegance.

Why the rivers won

The braided rivers of the eastern South Island — the Waitaki, the Rakaia, the Rangitata, the Waimakariri — are not really rivers in the European sense. They are gravel plains that happen, intermittently, to have water in them. The water threads itself through hundreds of shallow channels, none of them deep enough for a propeller, all of them full of stones the size of grapefruit. From a Mackenzie Country runholder’s point of view, this was a permanent inconvenience. There were stations and high-country huts you could see from the bank, plain as day, two hours’ drive upstream, that you could not reach in any conventional boat.

Hamilton had been thinking about this since the 1920s. The propeller was the obvious enemy. Anything spinning under a boat in fifteen centimetres of water and rolling shingle was going to be smashed inside a season. What he wanted was a boat with no moving parts below the waterline at all.

The braided Waimakariri River at sunset, threading hundreds of shallow channels through pale gravel
The Waimakariri above Christchurch — one of the Canterbury braided rivers Hamilton wanted to navigate. Hundreds of shallow channels in centimetres of water, on a bed of moving stones. Photo Michal Klajban, CC BY-SA 4.0.

Three ways to push a boat through water

It helps, here, to be concrete. There are three ways to push a boat. The Archimedes screw — the design Archimedes is supposed to have devised in Syracuse around 250 BC — is essentially a tilted corkscrew turning inside a tube. Each turn of the screw lifts a quantity of water along the tube. It moves a lot of water slowly, which is why for two thousand years it was used to lift water out of mines and onto fields, and why nobody ever tried to power a fast boat with one.

The propeller, refined into its modern form in the 1830s, is the opposite. A few angled blades spinning at high speed in open water cut through it like a fan, throwing it backwards and dragging the boat forwards. It is brutally efficient in deep clean water. It is useless in fifteen centimetres of moving shingle, where the blades hit stones and the boat hits the bottom.

The waterjet impeller, which is what Hamilton built, sits inside the hull. Imagine a section of pipe running fore and aft through the bottom of the boat. Water enters at the front through a grille flush with the hull. Inside the pipe a high-speed impeller — vanes on a shaft, much like a centrifugal pump — drives the water rearwards along the tube. The water leaves out the back at high velocity through a steerable nozzle. Newton does the rest. There is nothing rotating below the boat; the only opening underneath is a slot the depth of a hand. Steering and reverse are managed by the angle of the nozzle, not by a rudder. You can turn a Hamilton-jet boat inside its own length at speed — the famous Hamilton spin — because the entire propulsion stream pivots in a fraction of a second.

It sounds simple. It is not. The hard part is squeezing useful efficiency out of an impeller spinning inside a duct against a head of moving water. The Italian engineer Secondi Campini and the American John Hanley had both filed patents for water-jet boats earlier in the century — Hanley’s Hydro-Jet of the late 1940s was a respectable test platform — and both had concluded that the system was inherently less efficient than the propeller. They were correct, in the limited sense that the waterjet wastes a small percentage of its input power against the drag of the duct. They were wrong in the more important sense, which Hamilton seems to have understood instinctively, that the propeller’s efficiency advantage was meaningless to a boat that could not get to the water it wanted to be on. The right comparison was not jet against propeller. It was jet against staying home.

Hamilton spent the early 1950s getting the rest of it wrong.

The boat that nearly didn’t work

His first attempt, in 1953, was a 3.6-metre wooden hull with a side-valve Ford 100E engine driving a centrifugal pump. He took it down to the Irishman Creek dam he’d built thirty years earlier and ran it up and down. It moved. Then he took it to the Waitaki and ran it slowly upstream, past gravel banks, in centimetres of water. It worked, in the strict sense that it travelled in the direction the bow was pointing. It was not fast. The first prototype, by family memory, made about eleven miles an hour, in conditions where it should have made twenty.

The problem was the nozzle. Hamilton had placed it underwater, on the assumption that the jet should leave the boat in the medium it was pushing against. This is intuitively obvious and physically wrong: an underwater nozzle wastes energy fighting back-pressure from the water around it. One of his men — the family memoir credits a farmhand turned engineer named Alf Dick, who had grown up using high-pressure firehoses — suggested the nozzle should come up out of the water and discharge into air. Hamilton tried it. The boat surged. The next refinement, an axial-flow impeller designed by his employee George Davison, doubled the speed again. By 1955 the boats were moving at fifty miles an hour over water you could barely paddle a canoe through.

The first commercial Hamilton jet boat, the Quinnat, was sold in 1954 and named for a Pacific salmon. Quinnat is also a Canterbury fishing word, used by anyone who had ever stood on the gravel of the Rakaia mouth on a March morning. It told you, before you saw the boat, where it had come from and what it was for.

The Christchurch Press sent a reporter to one of the early trials on the Waitaki. The reporter, who clearly had not believed the story before he arrived, watched the boat go up a stretch of river over which a propeller boat would have ground its lower unit into scrap. He went back to Cathedral Square and wrote it up under a headline about a boat that had cheated the Waitaki, and the orders started arriving. Within two years the woolshed at Irishman Creek had been pressed into service as an assembly line. By 1957 the Christchurch factory was building forty units a year. By 1960 it was building several times that.

Hamilton was characteristically modest about the achievement. Asked, more than once, who had invented marine jet propulsion, he gave a version of the same line. “The honour belongs to a gentleman named Archimedes,” he said, “who lived some years ago.”

A modern Hamilton jet boat throwing a rooster tail of spray on the Dart River in Otago
A Hamilton jet on the Dart River, Otago. The discharge nozzle is visible above the waterline at the stern — the design move that made the boats fast. Photo AndrΓ© Richard Chalmers, CC BY-SA 4.0.

The Colorado run

By 1960 the boats were good enough to attract American attention. Otis “Dock” Marston, the most experienced commercial river runner in the United States, came to New Zealand, looked at the boats, and asked Hamilton whether they could climb the Colorado. Marston had run the Colorado downstream more often than anyone alive. He had also been on three failed attempts to run it the other way. The Grand Canyon, all 277 river-miles of it, had never been navigated upstream. Several people had drowned trying.

Hamilton agreed. He sent four eighteen-foot aluminium boats — the Kiwi, the Wee Red, the Wee Yellow and the Dock, named after Marston — each fitted with two Hamilton jet units behind a 185-horsepower Buick V8. He sent his son Jon, who was by then the company’s most experienced jet driver, and a small crew of New Zealand and American men. Marston came along to read the rapids.

The expedition started by running downstream from Lee’s Ferry to scout the rapids. At Lava Falls one of the drivers broke his leg in a swamping; he was lifted out by helicopter. The team turned around at Lake Mead and on 4 July 1960 began the run back up. The Wee Yellow was lost in Grapevine Rapid, swamped and sunk; her crew was pulled out, abandoned the run, and walked out. Three boats reached Lee’s Ferry on 12 July. Time magazine ran the story. Life ran photographs. The boats were displayed afterwards alongside John Wesley Powell’s 1869 expedition skiff at the Smithsonian.

It is, sixty-six years later, still the only successful upstream powered ascent of the Grand Canyon. The U.S. National Park Service has banned commercial jet-boat traffic on most of the river since the early 1970s. Lava Falls has not been climbed under power since.

For Hamilton, watching from a phone in Christchurch, the Colorado run did two things. It made the company internationally credible — orders followed within weeks, from the United States, Canada, Africa and South-East Asia — and it confirmed something he already believed, which was that the most useful tests of a piece of equipment are the ones the equipment was not designed for.

The detail that the Hamilton family liked best, in the years afterwards, was a quieter one. Marston, the great Colorado runner, kept asking how Jon had managed Lava on the second day, when he had to drive each boat up alone and then walk down through the rocks for the next. Jon, by family memory, said that he had simply waited for the standing wave to drop into the right shape, and then gone. There was no other technique to describe. He did it five times, on five different boats, in three days. He was thirty-five years old.

The family firm

From the late 1950s the focus of CWF Hamilton & Co shifted from earthmoving and hydroelectric work toward marine propulsion. The Christchurch factory began producing larger jet units for commercial vessels — harbour ferries, search-and-rescue craft, fishing boats. By the mid-1960s the company was supplying jets to overseas customers from a dedicated marine division. Bill Hamilton retired as managing director in 1965, although he continued to come into the works most days when he was in town. He was made an OBE in 1961, a Knight Bachelor in the 1974 Queen’s Birthday Honours, “for services to manufacturing”. He preferred Bill.

Two things kept the firm distinctive after Hamilton stepped back. The first was that it remained, and remains, in the family. CWF Hamilton & Co Ltd is still privately held by Hamilton descendants in Christchurch; Hamilton Jet, its principal trading arm, employs around 440 people at Middleton and exports to more than fifty countries. It is, in 2026, the world’s largest manufacturer of waterjet propulsion units, supplying everything from the Royal New Zealand Navy’s patrol vessels to U.S. Coast Guard fast-response craft to Norwegian rescue boats. Bill Hamilton’s grandson Mike Hamilton was, until recently, a senior figure on the board.

That family-firm structure is unusual at this scale. Most engineering companies of comparable global reach are publicly listed, or owned by larger industrial groups, or both; their decisions are made on a quarterly cycle by people with no particular attachment to where the factory is. Hamilton Jet’s decisions are made on a longer cycle by people who grew up around the works. The company puts a non-trivial fraction of revenue into research and development — the kind of long-payback investment a publicly listed firm would find harder to defend — and it has refused, so far, to move the design and manufacturing functions out of New Zealand. The old industrial economists’ phrase for this is “patient capital”. It is not a phrase Bill Hamilton would have used. He would have said the family was simply doing the obvious thing.

The second was that the technical roadmap Hamilton sketched in the 1950s — ducted axial-flow impeller, above-water steerable nozzle, no underwater rudder, no underwater shaft — turned out to scale. The Hamilton 400 series, introduced in the late 1970s and the first jet unit designed under CAD, propelled craft up to thirty metres long. Modern Hamilton waterjets push high-speed ferries at fifty knots and naval vessels at speeds the makers do not advertise. The propulsive geometry is the same one Bill drew in pencil on the back of a Ministry of Works envelope in 1953.

Huka Falls Jet boat performing a tight spin in front of Huka Falls on the Waikato River
The Huka Falls Jet on the Waikato. The Hamilton spin — a 360-degree turn at full speed within the boat’s own length — is possible because the entire propulsion stream pivots through the steerable nozzle. Photo Egghead06, CC BY-SA 3.0.

Hillary, the Ganges, and the long tail

In 1977, Sir Edmund Hillary led the Ocean to Sky expedition, an attempt to drive jet boats from the mouth of the Ganges to its Himalayan source. The boats were Hamiltons, three of them; the lead driver was Jon Hamilton; Bill’s grandson Mike Hamilton was on the crew, alongside Hillary’s son Peter. They went 2,400 kilometres up the Ganges in jet boats no larger than the ones that had run the Colorado seventeen years earlier. Hillary, by then sixty-eight, fell ill at altitude and did not summit Akash Parbat with the climbing party, but he reached the upper river. The expedition film, from the Ocean to the Sky, became one of the better-loved New Zealand documentaries of its decade.

By the time the Ganges expedition came back, Bill Hamilton was eighty and unwell. He died at Fairlie on 30 March 1978, six months after Hillary’s boats reached Hardwar. Peggy survived him by four years. They are buried in the Mackenzie Country.

What he was actually like

The temptation, with a man like Hamilton, is to write him up as a Boy’s Own caricature — the rugged Kiwi bloke who solved everything with a number-eight wire and a pipe. He was not that. He was a serious self-taught engineer with a serious technical library, a serious interest in motor cars, aircraft and hydraulics, and a serious preference for letting other people speak. The phrase his employees most often used about him in interviews was “you were rather in awe of him”, a reaction not generally produced by farmers in flannel shirts. He read German engineering papers in translation. He hired graduate engineers from Canterbury University when most New Zealand workshops would not. He was, by all accounts, a difficult man to work for if you cut a corner, and an extraordinarily generous one if you tried something hard and failed.

He was also, in a way that does not always come through in the company brochures, a high-country pragmatist. The high country in his lifetime had something most of New Zealand did not yet have, which was a chronic shortage of labour. There were never enough men. The economic logic of his entire career — excavator, ski tow, jet boat, even the small hydro plant at Irishman Creek — was that if you could not have more men you had to build better machines. The waterjet was, among other things, an answer to the problem of a high-country shepherd who needed to look at stock on the far side of a braided river and did not have a horse, a bridge, or a helper.

Sir Tim Wallis, who did much the same trick a generation later with helicopters and live deer recovery, used to say that the South Island made a particular kind of mechanical mind: the kind that, faced with an empty paddock and an obvious problem, started thinking about a machine. Hamilton was the first and probably the most consequential of that kind. Wallis flew Hamilton-jet rescue boats off the West Coast as part of a deer-recovery operation in the 1970s and considered them, in his own phrase, the most useful piece of New Zealand engineering of his lifetime.

Peggy’s memoir, Wild Irishman, is in some ways the more revealing source. She wrote about a man who could not stop sketching. There was always a small stub of pencil somewhere on him, and the back of any envelope, packet of cigarettes or feed-bag label was a candidate surface. He drew impellers, ducts, scoop angles, ski-tow gearings, hydraulic rams. He drew them at the breakfast table and at the woolshed and on a Tasman ferry. He left them lying around the house. Peggy collected hundreds. Many of them, she noted gently, were of the same problem in slightly different forms; he was working on something for years before he built it.

Why he matters now

New Zealand has a habit of treating its world-class manufacturers as either oddities or museum pieces. Hamilton Jet is neither. It is a privately owned, family-controlled, world-leading specialist engineering firm, designing and exporting some of the most technically sophisticated marine propulsion in the world from a factory ten minutes from the centre of Christchurch. It does this on a continent where most countries gave up on that kind of business twenty years ago.

It does it because Bill Hamilton, in 1953, refused to accept that the rivers he wanted to drive on were not the kind of rivers anyone built fast boats for; and because his children, and his grandchildren, refused to sell. The company has been offered, more than once, sums of money that would have ended its independence. It has not taken them. New Zealand is a richer country for that decision in ways that do not show up in the GDP figures.

The other thing Hamilton stood for, which is harder to put into a sentence, is the high-country answer to the question of what New Zealand industry is supposed to look like. Not branch plants of foreign giants. Not cheap commodity manufacturing. Not an export trade based entirely on grass. Something more like a small, technically ambitious, family-controlled firm that solves a hard problem better than anyone else in the world, and stays where it started.

The shed at Irishman Creek is still there. It is on private land, and you cannot visit it without permission, but the original lathe is in it, and the river it overlooks is still too shallow for a propeller. There is something to be said for the country that produced the man who, faced with that fact, sat down and built a different kind of boat.

Sources and further reading

Have your say

Did your family use a Hamilton jet on the Rakaia, the Waiau or the Buller? Did you crew on the Colorado run, the Sun Kosi, the Sepik or the Ganges? Did your dad work at the Middleton plant when the 400 series was on the drawing board? We’d like to hear your stories. Drop them in the comments below.

This article was written by AI, briefed to report the facts, hopefully without some of the bias people bring to the job πŸ™‚

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *